Posts

Chosen Solution I have a SK100 with no backlight, so I tried replacing the display with a replacement direct from Sennheiser and am still having no luck, any suggestions? The led is mounted on the main board. It is incredibly small and has to be soldering in the correct orientation for polarity (it is a diode). Look for the triangle mark on the old one for to orient the new one (bottom of triangle points towards bottom of circuit board)....

Chosen Solution I just replaced my MacBook battery using iFixit and followed all the instructions and everything was re-connected (to my knowledge.) I put the case back on and I went to turn it on and it would not. I then plugged it into the charger and it turned on. When I checked the battery it states “Battery not charging” and shows the source as the power adaptor. I went back and unplugged / replugged in the battery connector....

Chosen Solution My tab says its charging but is dropping in percentage why? that’s really common (at least in my life) firsto of all download “Galaxy Charging Current” and plug your phone in and check how much mA flows it should be 999mA or more i’m kinda 90% sure that it will be less than that so there are few things that effect that Bad or $@$*!& charger Bad or $@$*!...

Chosen Solution Hello today i bought a new motherboard for my Galaxy s5. When i replaced it and I tried to charge it I got the Battery temperature too low warning. I tried a new usb board it didn’t work I tried a different battery it didn’t work again I tried my old motherboard and it was working fine , so it seems that the motherboard that i bought is faulty is there a way to fix it with soldiering ?...

Chosen Solution I have a pair of green Patagonia baggies that are about 10 years old — they’re super comfy, totally functional, and still look fantastic. Unfortunately, the elastic waistband is completely shot, so the drawstring is the only thing keeping them up. I’m not ready to retire them yet, so is it possible to replace the elastic in that waistband? Hi Guv! It is entirely possible to replace the waistband....

Chosen Solution Hey I have a G3 and I recently replaced the screen with the entire frame.. After installing it worked fine. But after five minutes the screen started to show me a bunch of thick white line going from one end to another of the screen. Would you guys have any idea why this is happening ? Bad connection to the daughter board on the bottom of the assembly

Chosen Solution i have replaced the brake light but it still does not work Anne, check fuse number 47 in the Under-the -hood fuse/relay box for continuity as well as fuse number 9 in the under-dash fuse box. Check your light bulbs, they are dual-filament bulbs (type 7443) 21/5W and are on top of the tailights. Check the Brake Pedal Position Switch, use a multimeter or continuity tester to make sure it is working....

Chosen Solution My Thermoscan suddenly stopped working properly… it started to show a “Hi” message a few times and now just shows “POS” error in the LED screen. No hits or falling, was working fine. I did replace batteries, clean contacts, change to Fº and Cº… it seems the sensor does not detect temperature. Is there any solution to this? Luis Caceres (POS = position error) The infrared monitor cannot find a temperature equilibrium and allows no measurement – Clear the display by changing the probe cover....

Chosen Solution can you bypass may dell inspiron 5421 14R bios password or administrator password can anybody help me please thanks and advanced Hi Had you tried this yet? https://bios-pw.org/ Updates from a user: mbnsfld each time required Ctrl + Enter, (Enter was the only instruction given on the unlock screen); each time it was the code next to “Dell from serial number” that worked. By the way, the code the site asks for is the serial number with the four character extension that shows up on the unlock screen where you’re asked for the password....

Chosen Solution Can I only change digitizer and not the LCD? My screen top layer is broken, the digitizer and lcd are fine, I don’t think there’s any way to change the top glass without changing digitizer and touch screen. You can cgange just the glass but this is not easy. In fact if you have never done this repaor before you are probably better off replacing the lcd. You can try to replace the glass but you will probably end up causing damage to the lcd therefore you you might have to get a new lcd after the glass replacement....

Chosen Solution Are they compatible or not? My logic board is dead and before putting one from 2015 I want to know if it is possible to use one from 2017 model. Thanks. Oh Boy! Not good … At this point the cost of a new system would be cheaper! Apple has dropped the price so low it doesn’t really make sense fixing this series when you need a display, keyboard/trackpad or logic board, between the cost of the part and the labor....

Chosen Solution USB port broken to use a wall charger, Can I use a wireless charger? 7th gen hd fire tablets and above support the wireless charger its 10w ,However most wireless chargers will work just line it up to correct spot

Chosen Solution I can’t control the volume when I connect my non-Bluetooth TV to my photive speaker via RCA cable. The speaker will work fine and I can increase or lower the volume when I Bluetooth connection to my phone. I’ve connected the TV to an HDMX speaker and it works fine, unfortunately, that speaker decided not to hold a charge. Any suggestions as to why this isn’t working correctly?...

Chosen Solution Hi, My 5,1 Mac Pro dual is missing a screw on one of the heatsinks/temperature sensor. I was only able to find a screw from a single cpu 4,1 Mac Pro. Are they interchangeable? @supagiant yes they are interchangeable. The Dual and Single CPU use the same Northbridge heatsink. Use this guide Mac Pro Single CPU Northbridge Heatsink Repair for the repair. You can always check places like this for replacement screws

Chosen Solution Hi, I’ve been having this problem non stop for months and months. Got an iPhone XS which is all working brilliantly, but apart from the 3 minute boot loop. Every 3 minute’s almost exactly it restarts on it’s own accord. After a lot of research, charge port seems to do this. I’ve tried 2 non-genuine ones from ebay and they both do the same. Does anyone have any UK links as to where I can buy a genuine OEM charge port that’ll stop the 3 minute boot loop?...

Chosen Solution Hi all, I really need some help with a broken 3DS. I bought it on eBay as broken/parts but it seems to have an issue I have never seen before. So when it arrived it doesn’t power on at all when you press the power button nothing happens no orange light no blue light nothing at all. I opened up the 3DS to have a look to see if there was any very obvious issues and there didn’t seem to be corrosion, broken pieces and water marks are intact....

Chosen Solution The JVC RC-X610 boombox, like a lot of JVC audio equipment, is surprisingly good but it lacks an external audio input. Even for an experienced electronic engineer the PCB’s are undecipherable without a service manual and schematic. I have found an very expensive copy of the service manual on eBay. Where do these sellers find their manuals I wonder? Can anybody point me to a repository of JVC service manuals or specifically, one for the JVC RC-X610 ?...

Chosen Solution I tried restoring the phone and updating, and it says it is unable to do it. This has happened to me I would just say if it was exposed to water just leave it to have the water dry up or in the speaker hole maybe use a hair dryer on medium setting os not too hot or cold. This worked for me after leaving it for 1 month to have the water dry

Chosen Solution I recently replaced the one of the mandrils on my riding mower (sears lt 2000 riding mower).while doing so I replaced the mower belt (the long one) and after 15 minutes of use the belt slipped off and is shredded inside.is the a tension thing involved,should I have adjusted something.the belt I put on it came from tractor supply whse,not a sears replacement.but it was the same length.help please....

Chosen Solution So I have the same problem as all of the other ones here. Blackscreen on the LED cinema display, but I do have audio and my Mac does recognizes the display. I disassembled it to see what went wrong. Does someone here see something wrong with these parts? I don’t see it. I know this will not be a 100% confirm of the problem but hey, maybe you see it!...